Installing FreePBX 12 on CentOS 6.5

 

Initial System Setup

Icon

You MUST run all of these commands as the root user!

Icon

You MUST disable selinux.  selinux can cause strange behavior during the install

Disable selinux

In /etc/sysconfig/selinux , change the following lines:

sed -i 's/\(^SELINUX=\).*/\SELINUX=disabled/' /etc/sysconfig/selinux

reboot, and verify the selinux status by running 'sestatus'. It should say:

SELinux status: disabled

Update Your System

yum -y update yum groupinstall core yum groupinstall base

Install Additional Required Dependencies

yum install gcc gcc-c++ lynx bison mysql-devel mysql-server php php-mysql php-pear php-mbstring tftp-server httpd make ncurses-devel libtermcap-devel sendmail sendmail-cf caching-nameserver sox newt-devel libxml2-devel libtiff-devel audiofile-devel gtk2-devel subversion kernel-devel git subversion kernel-devel php-process crontabs cronie cronie-anacron wget vim php-xml uuid-devel libtool sqlite-devel

IPTables

Icon

Keeping IPTables turned off indefinitely is strongly discouraged. You will incur the wrath of high fees and hackers

You must disable the default iptables.  You can re-enable it later, once you have made the appropriate changes.  Information on iptables can be found with a quick Google search.  If iptables is left running, it will (at very least) block you from accessing the web interface.

See the current status:   

chkconfig iptables --list

Disable iptables:

chkconfig --level 0123456 iptables off

Stop the service (this skips rebooting again):

service iptables stop

Auto Start MySQL

You must have mysql running for freepbx to operate normally.  You need to set it to start at boot time. with the following command:

chkconfig --level 345 mysqld on

Then start mysqld if you don't plan on rebooting during the installation phase:

service mysqld start

Setup a password for mysql

mysql_secure_installation

 

Auto Start Apache

You will want Apache running, so you can access the FreePBX admin interface,  You need to set it to start at boot time. with the following command:

chkconfig --level 345 httpd on

Then start apache if you don't plan on rebooting during the installation phase:

service httpd start

Install PearDB

pear channel-update pear.php.net pear install db-1.7.14

Icon

You may receive a warning:

WARNING: "pear/DB" is deprecated in favor of "pear/MDB2"

At this time it is safe to ignore that message

Reboot server

reboot

Install Dependencies for Google Voice (If needed/wanted)

Install iksemel

cd /usr/src wget https://iksemel.googlecode.com/files/iksemel-1.4.tar.gz tar xf iksemel-*.tar.gz cd iksemel-* ./configure make make install

Add the Asterisk User

adduser asterisk -M -c "Asterisk User"

Install and Configure Asterisk

Download Asterisk source files.

cd /usr/src wget http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete/dahdi-linux-complete-current.tar.gz wget http://downloads.asterisk.org/pub/telephony/libpri/libpri-1.4-current.tar.gz wget http://downloads.asterisk.org/pub/telephony/asterisk/asterisk-13-current.tar.gz git clone https://github.com/akheron/jansson.git wget http://www.pjsip.org/release/2.2.1/pjproject-2.2.1.tar.bz2

Compile and install DAHDI and LibPRI

Icon

If you don't have any physical hardware you don't need to run these commands, however, it is still suggested to compile the modules, to allow you to add hardware later.

cd /usr/src tar xvfz dahdi-linux-complete-current.tar.gz tar xvfz libpri-1.4-current.tar.gz rm -f dahdi-linux-complete-current.tar.gz libpri-1.4-current.tar.gz cd dahdi-linux-complete-* make all make install make config cd /usr/src/libpri-1.4.* make make install

Compile and install pjproject

Icon

If you are doing this on a 64 bit system, please note that you MUST set the following during configure:

--libdir=/usr/lib64

cd /usr/src tar -xjvf pjproject-2.2.1.tar.bz2 cd pjproject-2.2.1 CFLAGS='-DPJ_HAS_IPV6=1' ./configure --prefix=/usr --enable-shared --disable-sound\   --disable-resample --disable-video --disable-opencore-amr --libdir=/usr/lib64 make dep make make install

Compile and Install jansson

Icon

If you are doing this on a 64 bit system, please note that you MUST set the following during configure:

--libdir=/usr/lib64

cd /usr/src/jansson autoreconf -i ./configure --libdir=/usr/lib64 make make install

Compile and install Asterisk

Icon

If you are doing this on a 64 bit system, please note that you MUST set the following during configure:

--libdir=/usr/lib64

cd /usr/src tar xvfz asterisk-13-current.tar.gz rm -f asterisk-13-current.tar.gz cd asterisk-* contrib/scripts/install_prereq install ./configure --libdir=/usr/lib64 contrib/scripts/get_mp3_source.sh make menuselect

You will be prompted at the point to pick which modules to build. Most of them will be enabled, but if you want to have MP3 support, you need to manually turn on 'format_mp3' on the first page.

After selecting 'Save & Exit' you can then continue

make make install make config ldconfig

Install Asterisk-Extra-Sounds

Note that this installs the (8khz) 'wav' soundfiles and G722 (High Definition 'Wideband') audio.

mkdir -p /var/lib/asterisk/sounds cd /var/lib/asterisk/sounds wget http://downloads.asterisk.org/pub/telephony/sounds/asterisk-extra-sounds-en-wav-current.tar.gz tar xfz asterisk-extra-sounds-en-wav-current.tar.gz rm -f asterisk-extra-sounds-en-wav-current.tar.gz # Wideband Audio download wget http://downloads.asterisk.org/pub/telephony/sounds/asterisk-extra-sounds-en-g722-current.tar.gz tar xfz asterisk-extra-sounds-en-g722-current.tar.gz rm -f asterisk-extra-sounds-en-g722-current.tar.gz

Install and Configure FreePBX

Download and extract FreePBX.

wget http://mirror.freepbx.org/modules/packages/freepbx/freepbx-12.0-latest.tgz

tar vxfz freepbx-12-latest.tgz

Set ownership permissions.

chown asterisk. /var/run/asterisk chown -R asterisk. /etc/asterisk chown -R asterisk. /var/{lib,log,spool}/asterisk chown -R asterisk. /usr/lib/asterisk chown -R asterisk. /usr/lib64/asterisk mkdir /var/www/html chown -R asterisk. /var/www/

A few small modifications to Apache.

sed -i 's/\(^upload_max_filesize = \).*/\120M/' /etc/php.ini cp /etc/httpd/conf/httpd.conf /etc/httpd/conf/httpd.conf_orig sed -i 's/^\(User\|Group\).*/\1 asterisk/' /etc/httpd/conf/httpd.conf service httpd restart

Configure Asterisk database in MYSQL. 

cd /usr/src/freepbx export ASTERISK_DB_PW=mysql-root-pass mysqladmin -u root create asterisk  mysqladmin -u root create asteriskcdrdb

Set permissions on MYSQL database.

mysql -u root -e "GRANT ALL PRIVILEGES ON asterisk.* TO asteriskuser@localhost IDENTIFIED BY '${ASTERISK_DB_PW}';" mysql -u root -e "GRANT ALL PRIVILEGES ON asteriskcdrdb.* TO asteriskuser@localhost IDENTIFIED BY '${ASTERISK_DB_PW}';" mysql -u root -e "flush privileges;"

Restart Asterisk and install FreePBX.

cd /usr/src/freepbx ./start_asterisk start ./install_amp --installdb --username=root --password=${ASTERISK_DB_PW} amportal chown amportal a ma installall amportal a reload amportal a ma refreshsignatures amportal chown

Icon

If you see an error about "Uncaught exception 'RuntimeException' with message 'gpg took too long to run.'" it is safe to run "amportal a ma installall" again.

Finally, one last mod and start FreePBX.

ln -s /var/lib/asterisk/moh /var/lib/asterisk/mohmp3 amportal restart

Start FreePBX

Navigate: 

http://yourlocalipaddress/html or if you prefer http://localhost/admin

Install and Setup Commercial Modules

Enable the FreePBX Commercial yum repos

wget -P /etc/yum.repos.d/ -N http://yum.schmoozecom.net/schmooze-commercial/schmooze-commercial.repo

yum clean all to clean out yum cache so it will find out new RPMs

yum clean all

yum install needed RPMs for Commercial Modules

yum -y install php-5.3-zend-guard-loader sysadmin fail2ban incron ImageMagick

Restart Apache and Install Sysadmin

service httpd restart

amportal a ma download sysadmin

amportal a ma install sysadmin




Change this on apache
nano /etc/httpd/conf/httpd.conf

Look for this line and coment None and add ALL

<Directory "/var/www/html">
  #AllowOverride None

  AllowOverride All

Restart apache with the following command

service httpd restart

--------------------------

amportal chown

amportal a ma refreshsignatures

amportal a reload




IPTABLES RULES

iptables -I INPUT 2 -m state --state NEW -m tcp -p tcp --dport 4445 -j ACCEPT 

iptables -I INPUT 2 -m state --state NEW -m udp -p udp --dport 5060 -j ACCEPT

iptables -I INPUT 2 -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT

iptables -I INPUT 2 -m state --state NEW -m udp -p udp --dport 10000:20000 -j ACCEPT



service iptables save